ul. Krzeczowska 20, 32-700 Bochnia 
+48 572 995 842 
Twój koszyk jest pusty!
Pobierz w formacie PDF
- Zgoda
- Szczegóły
- O plikach Cookie
Work smoothly with diagrams and boardview.
Repair devices with knowledge of dependency procedures.
Learn to distinguish and repair lines 5VL, 5VALW, 5VSUS and 5VS.
+23% VAT
Start 03.02.2025
Zostało 1 miejsce
Formy płatności
Najbliższy termin szkolenia
Start 03.02.2025Koniec 07.02.2025
Forma
Szkolenie hybrydowe 40 teaching hours (5 days)
Poziom
Intermediate level
Potrzebujesz pomocy?
Zamów bezpłatną konsultacjęAfter completing the training, the participant will learn to diagnose and interpret the starting procedure signals, using knowledge of the ACPI standard. The training will provide practical knowledge of the relationships between power lines and how to detect complex problems that prevent the device from starting.
Zostaw swój numer, nasi konsultanci odpowiedzą na Twoje pytania.
Zamów bezpłatną konsultację
Najbliższy termin 
40 teaching
Forma
Intermediate Rozwiń wszystko 
szczegóły
szczegóły
szczegóły
Classes are conducted in specially prepared and adapted rooms.
Room No. 1 consists of 6 workstations where training participants gain theoretical and practical knowledge.
Room No. 2 consists of 6 workstations where training participants gain theoretical and practical knowledge.
Room no. 3 consists of 8 workstations where training participants gain theoretical and practical knowledge.
What we send during the training:
tip soldering iron, hot air soldering iron, laboratory power supply with cables, smoke vapor absorber, EPZ programmer, silicone soldering mat, measurement probe, multimeter, ESD brush, pendrive, box with small service tools: (set of necessary screwdrivers, opener , spatula, tweezers, knife, soldering binder, absorbent tape, flux, binder extractor, pliers, isopropanol, prepared laptops/motherboards with ready-made faults, visualizer, antistatic apron.
8:45 - Start of training.
10:15-10:30 - Break 15 min.
12:00-12:45 - Lunch break 45 min.
14:15-14:30 - 15 min break
16:00 - End of training.
Each student completing the training on site has coffee from an espresso machine, biscuits, tea and water at their disposal. Lunch is included in the price of the training.
Jeśli masz pytania, skontaktuj się z nami, chętnie Ci pomożemy. Jesteśmy dostępni od 8:00-16:00.
Aleksandra Dziadowiec
tel: +48 572-995-842
E-mail: adziadowiec@notemaster.pl
If you need help with equipment for a training station, our team is available 24 hours a day.
Maciej Piela
tel: +48 518-115-526
E-mail: mpiela@notemaster.pl
After completing the training, each participant receives a Notebook Master certificate and an electronic certificate.
The certificate contains: the name and surname of the participant, the name of the training, the number of hours of training, the name and address of the organizer, the deadline for completing the training, the certificate number and the date of issue, the MSUES quality mark and the mark of entry into the Register of Training Institutions (RIS). Moreover, after completing each stage of training, the participant receives a certificate confirming its completion. The document contains the above information and the name of the stage.
After the course, you will receive training materials that will help you improve your knowledge when working independently as a service technician repairing electronic equipment.
IT Trainer
Electronics, BGA, programming.
medium
Electronics repair training is a technical training that requires high manual precision, thinking and perceptiveness from the participant. Consolidating these skills requires discussion of many topics. In short, a lot of analysis, soldering, replacing elements. A few days are the necessary minimum for each module to absorb the acquired knowledge effectively.
During the training, which lasts as long as 5 days, with knowledge in the first area, you will receive defects prepared for repair. Your task will be to analyze the diagram, perform measurements, make a diagnosis and then repair the board so that it works properly.
Everyone works on a separate case. If you get past the first glitch that leads to a short-circuit test, you'll get another, more difficult one. Damaged converters, damaged control systems lead you to the most difficult faults, where the motherboard shows no dysfunction in basic measurements, but there is no signal to complete the start procedure.
This part of the course is devoted to detailed learning how to work with technical documentation. It will require your maximum concentration and 100% attention. Without the knowledge acquired during this training, it will be difficult for you to find your way when trying to diagnose complex faults. However, if you have already learned all the topics on the agenda, we cordially invite you to learn how to solder BGA systems and use an oscilloscope. Also try your hand at the workshops offered by the fourth stage.
Based on our service and training experience, we have developed a system of effective remote learning. Remote learning can be as effective as on-site learning. We make sure to provide you with all the tools/equipment necessary for training. Your task will be to arrange them ergonomically. For some devices, you will also be able to use your workshop equipment. By working remotely, you will have the comfort of learning in your favorite space, while having the resources from our stationary workstation. In practice, the effects of remote learning will depend on the same as in the case of its stationary counterpart - due to the highly technical type of training, your 100% attention will be needed. During the training, make sure you have a place where no one will distract you during the course - you will see that learning even such a technical topic as electronics repair can be effective remotely!
At the first stage of our training, you will receive a lot of practical information about the selection of equipment, service chemicals and effective tools. You will also learn about the multitude of useful addresses on the Internet and how to obtain technical documentation. We will also show the sets of diagnostic applications necessary for every technician and how to use them.
While performing the directed exercises, which constitute the majority of the training, all students work on identical boards. You will get both functional (to investigate dependency processes) and damaged (to repair) devices. We make sure to present as many design aspects as possible, showing small differences and numerous similarities in subsequent generations. Therefore, the course will feature boards with various x86 architectures, dominated by Intel and AMD systems. In the workshop part, everyone has an individual case - you can work both with equipment provided by us or with your own. By removing the fault on the motherboard, you will be able to check for yourself whether you have made the correct diagnosis and repair, verifying the correct operation of the device. The number of repaired boards depends on the pace of your work. The faults you will have to deal with include: short circuits in power supply branches, damaged active elements, failures of logic and power supply systems - in short, a full range of possibilities.
We design our training so as not to absorb your time outside the course hours. Mastering the knowledge from the first stage is enough to start learning how to work with technical documentation. In the case of the online form, we recommend checking the sent equipment with the provided checklist and preliminary preparation of the workstation to be able to effectively acquire knowledge during meetings.
